深圳市南山区嘉泰姆电子经营部 已通过实名认证

一、基本特性Basic characteristics
1、 线圈参数Coil specification
      (1) 额定电压Nominal voltage    DC 12V
       (2) 线圈阻抗Coil resistance     155Ω±10% (at 23±5℃)
      (3) 额定电流Rated current        DC 78mA±10% (at 23±5℃)
     (4) 动作电压Operate voltage      DC 9.0V Max ((at 23±5℃)
     (5) 释放电压Release voltage      DC 0.6V Min ((at 23±5℃)
    (6) **电压Maximum voltage    DC 15.6V(130% of nominal voltage)
     (7) 线圈温升Coil temperature rise     50K Max (Coil:12V; Contact:20A)
2、 触点参数Contact Specification
    (1) 触点型式Contact configuration      SPDT (1 Form C)--单刀双掷（一组转换）
    (2) 触点额定负载Contact rating           20A 277VAC;20A/10A 250VAC (Resistive load)
                                                            40A/30 250VAC(Resistive load) available；
   (3) 接触电阻Contact resistance          Initial（初始值） 100 mΩ Max (At DC6V 1A)
   (4) 动作时间Operate time                  20ms Max
   (5) 释放时间Release time                  20ms Max
   (6) **动作频率Maximum operating           Mechanically 18000 cycle/h（机械）
                                                                    frequency Electrically 600 cycle/h（电气）

  (7) 触点温升Contact temperature rise          50K Max (Coil:12V;Contact:20A)
3、 通用参数General Specification
  (1) 绝缘阻抗Insulation resistance          1000MΩ Min (at DC500V)

  (2) 电气强度Dielectric strength

      触点间between open contacts           1500VAC,50/60 HZ for 1Minute

     线圈与触点间between contacts and coil     2500VAC,50/60 HZ for 1 Minute 4000VAC,50/60 HZ for 1 Minute（高耐压型）

  (3) 环境温度Ambient temperature       -40℃～+85℃ (Not freezing and condensing at low temperature)

  (4) 相对湿度Relative Humidity            45% to 85% RH

  (5) 电气寿命Electrical life            100,000 Operations Min (at 20A 277VAC)

  (6) 机械寿命Mechanical life          10,000,000 operations Min
4、 体系、安规认证和环保Quality System、Safety Certification and RoHS(REACH)

   (1) UL certified File NO. E341498； 20A 277VAC；30A 277VAC；

  (2) TUV certified File No. R50198473 30A 240VAC；20/10A 240VAC

  (3) CQC certified File No. CQC 30A 250VAC；20A/10A 250VAC

  (4) ISO9001:2008 certified File No. 05311Q22581R0S

  (5) RoHS and REACH Compliant

二、环境参数Environmental Characteristics
1、 抗振动性Vibration resistance
      1.1 误动作Error operation 在X、Y、Z轴三个方向施加双振幅为1.5mm，频率为10-55HZ的振动，时间5分钟，误动作时间不超过1ms。 

           At    constant vibration of double amplitude 1.5mm, 10～55 HZ , in each direction of X,Y,Z for 5 minutes. No error   

           operation more than 1 ms.
1.2 耐久性Endurance
       在三个方向施加振动2小时，无结构损坏。 No construction trouble when vibrate it from 3 directions for 2 hours.( Amplitude

      1.5mm, 10～55 HZ)
2、 抗冲击性Shock resistance
      2.1 误动作Error operation 在三个方向施加三次加速度为100m/s2 持续时间11ms，误动作不超过1ms。 At peak acceleration 100m/s2， duration 11ms, 3 shocks is given in each direction of X, Y, Z. No error operation more than 1 ms.
2.2 耐久性Endurance
      三个方向三次加速度为1000m/s2 持续时间6ms，无结构损坏。 No construction trouble when shock it from 3 directions 3 times at peak acceleration 1000m/s2， duration 6ms.
3、 耐寒性Cold resistance
     3.1 耐寒性Cold resistance 放置于–40℃±2℃环境温度下240小时，然后在标准条件下放置2小时，结构和性能无异常。 No any trouble on construction or characteristic when leave relay in –40℃±2℃ for 240h. After that, leave it in standard condition for 2 hours.
4、 耐热性Heat resistance
     4.1 耐热性Heat resistance 放置于+85℃±2℃环境温度下240小时，然后在标准条件下放置2小时，结构和性能无异常。 No any trouble on construction or characteristic when leave relay in +85℃±2℃ for 240h. After that, leave it in standard condition for 2 hours。
5、 耐湿性Moisture resistance
     5.1放置于40℃, 湿度90%环境下240小时，然后在标准条件下放置2小时，绝缘电阻最小10MΩ，结构和性能无异常。 After keeping relay for 240h in 40℃, 90%, then leave it in standard condition for 2 hours。Insulation resistance 10MΩ Min. No any trouble on construction or characteristic.

三、端子性能Terminal characteristics

     1、端子强度Terminal strength

        在端子上施加10N压力10秒钟，无变形现象。 10N pushed into any terminals for 10 s. There shall be no abnormalities. (The curving of the terminals shall be acceptable)

    2、端子可焊性Terminal solderability

        端子浸入260±5℃焊锡槽中，时间5±0.5 s ，90%部位应该上锡。 In case of lead free solder 260±5℃, 5±0.5 s , 90% of the dipped portion shall be soldered.

3、耐焊接热Soldering thermal

    端子浸入260±5℃焊锡槽中，时间10±1 s，结构和性能无异常。 No any trouble on construction or characteristic. When dipped into solder bath 260±5℃, 10±1s.

四、标准测试条件Standardard test condition

      1、环境温度Ambient temperature 23±5℃

      2、相对湿度Relative humidity 25%～75%

     3、气压Air pressure 86kPa～106kPa

     4、测试位置Direction of Test 端子朝下位置Terminals down position

五、储存条件Storage condition

    1、环境温度Ambient temperature -40℃～+85℃

    2、相对湿度Relative humidity 35%～85%

    3、环境Environment

        3.1、不要储存在诸如硫化氢和盐雾气体等有腐蚀性的环境中。 Store in locations where the product or container is not expose to corrosive gas such as hydrogen sulfide or salty air.

       3.2、储存在没有可视尘埃的环境中。 Store in locations where no visible dust exists. 3.3、储存在没有直射阳光的环境中。 Store in locations not subject to direct sunlight.

六、外型图、线路板孔位图和线路图Outline、PCB Layout and Wiring diagram(unit:mm)