企业特殊行业经营资质信息公示
营业执照已认证 
点击图片查看原图德国倍福XTS线性传输系统
贝克霍夫的线性传输系统。两种经过验证的驱动原理-结合成一种新的驱动技术。随着XTS(扩展传输系统)线性传输系统，贝克霍夫提出了一种驱动器解决方案，这是****的解决方案-因为它结合了两个**的驱动原理的优点，在一个单一的系统。在以前使用旋转电机的可能性已经结束的地方，XTS增加了线性系统的优点。到目前为止，在纯线性系统的使用范围有限的地方，XTS补充了旋转解决方案的好处。特殊需求需要特殊的解决方案，这就是为什么开发完全封装的XTS卫生版本和XTS黑线来补充XTS标准的原因。
线性传输系统XTS(ExtendedTransportSystem)结合了旋转系统和线性系统的优点。XTS是一个机电一体化系统，它包含操作所需的所有功能：模块化的、完全集成的线性电机，在单个装置中进行电力电子和位置测量，作为移动部件的推动器和机械导轨。通过这几个协调的组件，可以实现*多样化的应用。所需的几何形状、长度和半径由元件的数量和选择组成。XTS使单个产品的运输具有持续的物料流动。由于建筑体积小，可以提高能源效率，并能显着地减少机器的尺寸。
System properties
XTS Standard
Max. force 100 N at standstill
Continuous force 30 N (at ~30 °C temperature increase in the motor compared to mounting frame)
Speed 4 m/s @ 48 V DC supply
Acceleration > 100 m/s? (without payload)
Positioning accuracy <±0.15 mm @ 1.5 m/s possible within a straight module
Absolute accuracy <±0.25 mm possible within a straight module
Repeatability <±10 μm (standstill unidirectional)
Mover length 50 mm in direction of movement
Mover weight approx. 410 g (complete mover without attachments)
Max. system length > 100 m (dependent on computing power, no system limit)
Operating/storage temperature -10…+40 °C/-25…+85 °C (for further information see documentation)
Protection class motor modules: IP 65 (for further information see documentation)
Approvals/Markings CE, UL
Vibration/shock resistance conforms to EN 60068-2-6/EN 60068-2-27
EMC immunity/emission conforms to EN 61000-6-2/EN 61000-6-4
Electrical data
XTS
Supply voltage control voltage 24 V DC, power supply 48 V DC
Current consumption power supply: 16 A nominal current
Power consumption 24 V DC motor modules: 30 W/m (communication, electronics, position determination)
Length per feed max. 3 m (voltage supply, EtherCAT)
Power consumption per mover approx. 30 W @ 2 m/s constant speed
XTS products
AT20xx-0xxx XTS motor module
AT901x-0050-0550 XTS mover
AT9xxx-xxxx XTS guide rails
AT2000-xx00 XTS starter kits
TF5850-00pp TC3 XTS Extension
AT20xx-0xxx
AT20xx-0xxx XTS motor modules
AT20xx-0xxx | XTS motor modules
The motor module, the power electronics and the displacement measurement are built into the profile. The power electronics are optimised for the requirement and reduce assembly expenditure. There is an upper mechanical interface to the guide rail and a lower one to the support structure. Straight segments and curves can be combined arbitrarily. The geometry of the motor module without edges and openings allows easy cleaning.
Double-air-gap motor
double-action linear motor, hence low resulting forces on the mechanical bearing and compact total solution
displacement measurement integrated, no additional assembly, no calibration
Tolerances are compensated automatically.
Attractive forces neutralise each other.
lower force effect (wear) on the guide
Friction losses are greatly reduced.
Output stages and coil package integrated
no cables between coil and output stage
no wiring expenditure
exclusion of errors
minimum mounting space
Output stage and coil are optimally matched to each other.
supply voltage 48 V DC (low voltage, low safety expenditure)
Independent supply of each individual coil with current is possible.
arbitrary number of travelling fields/movers possible
temperature monitoring of the output stage
temperature model of the coils for optimum peak load use (I²T model)
low temperature rise due to good thermal coupling to the machine bed
AT20xx-0xxx XTS motor modules | Curved motor module, +22.5°
Curved motor module, +22.5°
AT20xx-0xxx XTS motor modules | Curved motor module, -22.5°
Curved motor module, -22.5°
AT20xx-0xxx XTS motor modules | Straight motor module
Straight motor module
AT20xx-0xxx XTS motor modules | Curved motor module, 180° (clothoid)
Curved motor module, 180° (clothoid)
AT9xxx-xxxx | XTS guide rails
The guide rail with the matching movers makes the XTS system a ready-to-use solution. However, the motor modules can also be used together with the magnetic plate sets as a custom solution without the XTS guide rail. The movers can be removed or inserted without tools through a lock by releasing two screws and removing part of the rail.
optimised solution for immediate mounting on the motor module
backlash-free due to low manufacturing tolerances and pre-tensioned rollers
abrasion-resistant hard anodized aluminium
free of abutting ends, lengths up to 2.5 m available
high-precision mounting by means of fits
easy maintenance through lock for the removal of the movers
Movers and guide rail are optimally matched to each other. The geometry of the aluminium rail and the hard anodized aluminium of the surface in combination with the running surface of the mover rollers allow good running characteristics and low wear.
AT9011, AT9012 | XTS movers
The movers are made of a light and solid aluminium alloy. Thanks to their arrangement the rollers allow backlash-free travel on the straights and in the curves. The coating of the rollers causes very little running noise and is particularly low-wear without lubrication of the guide rail. The attractive forces of the magnetic plates are largely balanced by the opposed arrangement, so that the rollers and the rail do not have to absorb the comparatively high attractive forces of the magnets.
The centre of the encoder flag supplies a position signal to the motor module. The encoder flag is made from a sturdy, lightweight glass-fibre reinforced material. A Mover 1 can be detected by means of a special magnetic plate set. This mover is always recognised as servo axis 1 and used as the first servo axis after start-up. All following movers (standard movers) are counted upwards. This results in a fixed assignment between axis numbers and movers, which is even retained after the system has been switched off.
The AT9011-0070-0550 mover provides an increased payload due to its overall length of 70 mm and larger rollers. The standard rail can be used for traveling in straight lines, adapted rails are necessary for traveling around corners. Therefore, a mixed operation of movers of different sizes is only possible when traveling in straight lines.
Features
no sliding contacts or cables to the moved part, purely passive mover
2 magnetic plates generate the controlled propulsive force via the motor module.
The attractive forces largely neutralise each other in relation to the guide mechanism.
low friction losses
An encoder flag generates the position signal.
Mover 1 – fixed assignment of mover to servo axis
Short mover length allows small product spacings.
Geometry allows driving through curves with full dynamics.
no development of heat on and in the mover
Ordering information
XTS mover suitable for the guide rail system AT9000/AT9050
AT9011-0050-0550 mover, 6 rollers (plastic coated), length 50 mm, 410 g, mounted with magnetic plate set AT9001-0550 (mover standard) and set of rollers ZX9011-0050
AT9011-0050-1550 mover, 6 rollers (plastic coated), length 50 mm, 410 g, mounted with magnetic plate set AT9001-1550 (mover 1) and set of rollers ZX9011-0050
AT9011-0070-0550 mover, 6 rollers (plastic coated), length 70 mm, 595 g, mounted with magnetic plate set AT9001-0550 (mover standard) and set of rollers ZX9011-0070
AT9011-0070-1550 mover, 6 rollers (plastic coated), length 70 mm, 595 g, mounted with magnetic plate set AT9001-1550 (mover 1) and set of rollers ZX9011-0070
AT9012-0050-0550 mover, 12 rollers (plastic coated), length 50 mm, 460 g, mounted with magnetic plate set AT9001-0550 (mover standard) and set of rollers ZX9012-0050
AT9012-0050-1550 mover, 12 rollers (plastic coated), length 50 mm, 460 g, mounted with magnetic plate set AT9001-1550 (mover 1) and set of rollers ZX9012-0050
Accessories
AT9001-0550 magnetic plate set mover standard, 5-pin, length 50 mm, preinstalled with 1.2 mm thick encoder flag, suitable for XTS standard movers
AT9001-0550-1640 magnetic plate set mover standard, 5-pin, length 50 mm, preinstalled with 1.6 mm thick encoder flag, suitable for external movers
AT9001-1550 magnetic plate set mover 1, 5-pin, length 50 mm, pre-installed with 1.2 mm thick encoder flag, suitable for XTS standard movers
AT9001-1550-1640 magnetic plate set mover 1, 5-pin, length 50 mm, preinstalled with 1.6 mm thick encoder flag, suitable for external movers
ZX9011-0050 set of rollers, 6 rollers (plastic coated), suitable for mover AT9011-0050-xxxx
ZX9011-0070 set of rollers, 6 rollers (plastic coated), suitable for mover AT9011-0070-xxxx
ZX9012-0050 set of rollers, 12 rollers (plastic coated), suitable for mover AT9012-0050-xxxx
Further XTS products
AT20xx-0xxx XTS motor module
AT9xxx-xxxx XTS guide rails
AT2000-xx00 starter kit
TF5850-00pp TC3 XTS Extension
AT2000-xx00 | XTS starter kits
The XTS starter kit facilitates fast and effective entry to the new technology. Mechanical tests and the programming of your own motion profiles are simple to accomplish. Programming experience in IEC 61131-3 and knowledge of TwinCAT NC are required for this. The XTS starter kit contains all components required for the operation of an XTS system. Depending on the required path length, a choice of three starter kits is available. The construction is fully functional and completely pre-assembled.
Basic components
stand and holder for all mechanical parts
Industrial PC with all necessary interfaces and sufficient system performance
TwinCAT NC PTP and XTS function package
installed in a control cabinet, fully wired, ready for operation
power supply units 24 V DC and 48 V DC
1 day instruction and programming support
Required user skills
practical experience with TwinCAT
basic knowledge of Motion Control
