企业特殊行业经营资质信息公示
点击图片查看原图用于各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面及烤(喷)漆面等制品的丝印及移印,不需加固化剂,不需烘烤,即可获得优异的附着力。
油墨特性:
1、平光、附着力佳、耐汽油、耐化学品;
2、手感好,流平性佳、面光洁;
3、表面硬度好,耐冲击性能强、抗刮伤;
4、耐汽油、耐酒精、耐化学品程度佳;
印刷:
选用网目为100-350目,以120T网纱计算涂覆盖面积每公斤达30~35㎡。
表干时间自然挥发5-15分钟,实干时间在24小时以内,48小时后达**性能。
1.用配套专用稀释剂开油水
2.用718洗网水洗网。
3.或添加配套硬化剂10%可增加附着力,提高墨膜硬度。
4.烤箱80℃烘烤10分钟佳能更优。
测试方法(完全干燥后):
1.3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。
使用方法:
1.建议用我公司专用稀释剂进行稀释,不建议使用783慢干稀释剂稀释,使用前应充分搅拌,用后随时密封。
2.搅拌时加本公司配套开油水10-12%,稀释到印刷适合粘度,移印稀释使用移印专用稀释剂;用718洗网水清洗。
3.不得与其它类型油墨混合使用,否则容易出现其他附着力,化学反应等不良现象。
4. 加入固化剂的油墨使用时限为8小时,过期请弃用,剩余油墨不可回收
注意事项:
1.各种承印物料的外观相似,但可能会是不同的材料,客户需先试印,确其符合要求后,再批量生产。
2.在移印过程中,如出现拉丝或散开,可适当加入一些慢干膏即可;
3.环境温度过高,将会影响油墨原有质量。白色超越150都会变色,烘烤时请用木质材料垫底进行烘烤,不得直接接触铁
4.根据气候变化,请远离火源,阴暗处15度-30度环境下存放
Oles MPE Plating Ink
MPE plating strengthening series ink characteristics : mainly used in plating surface, enhanced surface, vacuum plating surface.PU surface.UV surface and other materials, with a high color, high color, high covering power, high stability, high alcohol and rub characteristics. Printing: screen printing can be. Surface drying and drying time: surface dry time natural volatile 5-10 minutes; work time within 24 hours. Dilution and cleaning: SV3 slow dry open water, UVK1 ( printing open water) can be simultaneously used 718 washing network water cleaning. Test method ( completely dry ): 1, 3M gummed paper in the paintings of the surface of the ink, 45 degree angle quickly pulled off the oil; 2, 99% of the purity of industrial alcohol, one kilogram of weight of cotton pack in the ink surface, with a horizontal force pulling back and forth 200 times without decolorization; 3: oak, wear resistance eraser 500g force level brush back and forth 500 times. Usage: 1, use should be fully stirred, use at any time after the closure; 2, add water mixing 10-15%, diluted to 3, screen printing viscosity; the plug is available when washing network water cleaning; 4, not with other types of ink mixing. Note: 1, the plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then batch printing; 2, in the printing process, such as drawing or spread out, may be appropriate to add some slow dry plaster; 3, the ambient temperature is too high, will affect the quality of the original ink; 4, according to climate change, please stay away from fire, dark environment storage.用于各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面及烤(喷)漆面等制品的丝印及移印,不需加固化剂,不需烘烤,即可获得优异的附着力。
油墨特性:
1、平光、附着力佳、耐汽油、耐化学品;
2、手感好,流平性佳、面光洁;
3、表面硬度好,耐冲击性能强、抗刮伤;
4、耐汽油、耐酒精、耐化学品程度佳;
印刷:
选用网目为100-350目,以120T网纱计算涂覆盖面积每公斤达30~35㎡。
表干时间自然挥发5-15分钟,实干时间在24小时以内,48小时后达**性能。
1.用配套专用稀释剂开油水
2.用718洗网水洗网。
3.或添加配套硬化剂10%可增加附着力,提高墨膜硬度。
4.烤箱80℃烘烤10分钟佳能更优。
测试方法(完全干燥后):
1.3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。
使用方法:
1.建议用我公司专用稀释剂进行稀释,不建议使用783慢干稀释剂稀释,使用前应充分搅拌,用后随时密封。
2.搅拌时加本公司配套开油水10-12%,稀释到印刷适合粘度,移印稀释使用移印专用稀释剂;用718洗网水清洗。
3.不得与其它类型油墨混合使用,否则容易出现其他附着力,化学反应等不良现象。
4. 加入固化剂的油墨使用时限为8小时,过期请弃用,剩余油墨不可回收
注意事项:
1.各种承印物料的外观相似,但可能会是不同的材料,客户需先试印,确其符合要求后,再批量生产。
2.在移印过程中,如出现拉丝或散开,可适当加入一些慢干膏即可;
3.环境温度过高,将会影响油墨原有质量。白色超越150都会变色,烘烤时请用木质材料垫底进行烘烤,不得直接接触铁
4.根据气候变化,请远离火源,阴暗处15度-30度环境下存放
Oles MPE Plating Ink
MPE plating strengthening series ink characteristics : mainly used in plating surface, enhanced surface, vacuum plating surface.PU surface.UV surface and other materials, with a high color, high color, high covering power, high stability, high alcohol and rub characteristics. Printing: screen printing can be. Surface drying and drying time: surface dry time natural volatile 5-10 minutes; work time within 24 hours. Dilution and cleaning: SV3 slow dry open water, UVK1 ( printing open water) can be simultaneously used 718 washing network water cleaning. Test method ( completely dry ): 1, 3M gummed paper in the paintings of the surface of the ink, 45 degree angle quickly pulled off the oil; 2, 99% of the purity of industrial alcohol, one kilogram of weight of cotton pack in the ink surface, with a horizontal force pulling back and forth 200 times without decolorization; 3: oak, wear resistance eraser 500g force level brush back and forth 500 times. Usage: 1, use should be fully stirred, use at any time after the closure; 2, add water mixing 10-15%, diluted to 3, screen printing viscosity; the plug is available when washing network water cleaning; 4, not with other types of ink mixing. Note: 1, the plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then batch printing; 2, in the printing process, such as drawing or spread out, may be appropriate to add some slow dry plaster; 3, the ambient temperature is too high, will affect the quality of the original ink; 4, according to climate change, please stay away from fire, dark environment storage.
